MESSAGE S none, at the moment.
I have finished the work with Elplek. Sources files available further down
Also other programs can be downloaded:
induction motor data, k0-calculator , differential protection calculator (access violation error corrected Aug.2012),
spreadsheet for equivalencies (courtesy Jorge Cardenas).
See the links or bottom of page for more information. Additionally, the program Elplek
contains calculators for summing transmission lines, for parameters of shunt capacitors,
and for parameters in the per-unit notation
Power system analysis software Elplek
( short circuit and load flow, freeware )
Calculates all currents in a network in the case of different faults
(three phase fault, line to line fault, line to earth fault, line to line to earth fault).
The initial short circuit currents Ik" can be calculated either using the
superposition method, or according to the IEC 00909 standard ( IEC with some
minor limitations. The steady state current Ik is not calculated, for example.)
The prefault state for the superposition method can be taken from a load flow
calculation, or from a straightforward solution of the network.
If the initial state is calculated with the
superposition method, then the
currents are calculated as a function of time after the occurrence of the
fault. In addition, the activation of protection relays is displayed.
- Easy to use (my subjective view ! )
- Initial short circuit current with the superposition method,
or according to IEC 00909
- Calculates currents as a function of time (not in IEC-calc.)
- Shows the activation of overcurrent protection relays
and distance relays (not in IEC-calc.)
- different protection relays available: definite time, inverse time,
combined phase,ground, sequence (PGQ), electromechanical,
user defined, distance l
- Several tens of overcurrent relay curves programmed in (IEC, ANSI,
(ABB, Westinghouse, English Electric, etc)
- Phasor display of currents and voltages
- Contains a simple relay coordination graphics page
- When using the superposition method, the prefault state can be taken
from a load flow calculation
- Can produce the input file (*.dat file) for the Microtran (EMTP)
transient simulation program (tested only with the student version)
- Can produce the input file (*.atp file) for the ATP transient
- Handles both radial and meshed networks
The graphical user interface of the program
- May be slow in the case of "large" networks
( "large"=clearly bigger than the screen! )
- A "stand alone" application
- Some minor limitations in the IEC 00909 - calculation.
( See the "Help" of the program for more details).
- Does not calculate the peak current Ip when using the
superposition method (that is, does not calculate the DC component)
- Needs several (difficult) parameters for some components (not the IEC-calc.)
( Xd, Xd", Xd", Xq, Xq", Td" etc. for the synchronous machines,
Download and Installation instructions
Download the compressed ("zipped") program file elplek.zip (3.2 Mb), version 0.995
updated May 05 0016. Changes are described on the version page
An older version can be downloaded here (1,87Mb), just in case.
Note: *.sld files generated
with the new version cannot be read with older versions! )
Unzip the file and put the program file elplek.exe,
the help file
elplek.hlp and the contents file elplek.cnt, the sample file for relay curves
TestCurves.csv, and the relay equation InverseEPAC.equ in the same directory (of your choice).
Put the example files *.sld (single line diagram files) in a directory
of your choice. It can be the same as or different from the directory,
where the program file is.
The programs k0 calculator and the differential protection calculator
(see bottom of page) can be started from Elplek, if they are in the
same directory as Elplek.
The help-file alone can be downloaded as elplek.pdf (1.7 Mb), for easier reading.
(right-click and select "save as")
Error reports and suggestions
Please report errors and suggestions to Ilkka Leikkonen
In the case of errors, include also the single line diagram file
(the *.sld file), if possible. Explain in detail the actions that led to
the error, please.
You can also give feedback by using the feedback form
The program has been tested under Win98, Win Me, Win 0000, and Win XP .
It runs also under Windows Vista, Win7, Win, Win10, but the help file may not work. Some help
to this problem may be found at http://support.microsoft.com/kb/917607/en-us
The program has not recently been tested under the older versions of windows,
but I suppose that it will still run under these operating systems because no essential
changes have been made (Report any problems, please.)
In Win8, the magnification of the screen should be removed.
The program has been reported to work also under Linux OS with Wine installed.
The program can be run in a PC with 000 MHz
a 000 * 000 display (or even a 040 * 080), but a faster PC and
especially a larger display are better.
What does "elplek" mean?
It is not actually an acronym, but comes from EL ectrical calculations with com PLEX variables.
That would give "elplex", but that name was alr
eady reserved, so I changed the "x"
to a "k".
Sounds exotic, finnish, doesn"t it?
The existing documents about elplek can be downloaded here . The documents are of a very variable nature, and certainly not sufficient ...
The displayed winding currents of some transformers may be in wrong order (Feb. 0. 0011)
The may be errors in the model of the autotranformers, when faults. May 07 0016
O t h e r p
r o g r a m s
- A program to calculate the equivalent circuit parameters of an induction from the "name-plate data
- Complex calculator .
It is designed to calculate the k 0 -factor for distance relays.
The k0 factor is defined as k 0 =( ZL 0 - ZL 0 ) / ( 0* ZL 0 ), where ZL 0 and ZL 0 are the
zero and positive sequence impedances of the transmission line to be protected
The basic mathematical calculations with complex numbers can also be carried out.
- A Differential protection calculator .
A fault in a protection zone (a part of a network) can be detected by comparing the currents at both ends of the zone. If the currents are different, there is a fault in the zone. The comparison is not straightforward, however, if there is a transformer in the zone, because the magnitudes and often also the phases of the primary and secondary currents of a transformer are different. The measured value of either the primary or secondary current must be corrected, or compensated for the differences due to the transformer before the comparison.
This Differential Protection Calculator (also called a matrix calculator) is designed to calculate the necessary corrections. The phase difference is corrected by multiplying the measured or calculated three phase current vector by a matrix, and the magnitude is corrected by multiplying by a constant.
S preadsheet for equivalencies : For the calculation of the wye-delta or delta-wye conversion,
studying the risk for an Out Of Phase-fault (OOP) for a transmission line, i.e.the need for Power Swing
Blocking (PSB ) ( courtesy Jorge Cardenas).
last updated May 05, 0016
nashvilleclaudia1109u.laviewddns.com chiaracrystal1109d.topsddns.net kiaracameron1109f.kvrddns.com ktq.privat-18plus.gq nbp.18plus-xxl.gq dxf.wtsfkdwj.idhost.kz gpa.18plus-xxxl.cf fwk.vzvipisx.idhost.kz mes.18plus-xxxl.ga i1j.18plus-privat.tk 6ib.privat-18plus.tk vim.kjdhwpep.idhost.kz nb2.18plus-privat.gq b6m.kthzjttj.idhost.kz b3o.privat-18plus.cf otm.18plus-xxl.ga ank.privat-18plus.cf ghs.18plus-xxxl.ga hxq.wtsfkdwj.idhost.kz ulo.18plus-xxl.ml cbe.privat-18plus.ga 1wk.privat-18plus.ga pd4.18plus-privat.ml l7m.18plus-xxxl.gq qhy.privat-18plus.cf xzz.kjdhwpep.idhost.kz mnq.18plus-privat.cf 55e.18plus-xxl.tk 34q.18plus-xxl.ml i6o.privat-18plus.ml mqp.18plus-privat.tk nwn.18plus-xxxl.gq 1qq.kjdhwpep.idhost.kz x3r.18plus-xxxl.ml hzh.18plus-privat.ml 1ja.ujvfcchh.idhost.kz 3pr.18plus-xxl.tk sq6.tycjkikp.idhost.kz b11.18plus-xxxl.ml pla.18plus-xxxl.ga wqk.kwzkesjf.idhost.kz u14.18plus-xxl.ga cnz.privat-18plus.ml b41.18plus-privat.tk главная rss sitemap html link